自2007年以來，EQUILIBAR為具挑戰性的應用提供了創新的壓力控制技術。EQUILIBAR的圓頂式多孔閥和調節器已成為精密的黃金標準。
主營產品
EQUILIBAR背壓調節器
EQUILIBAR真空調壓器
EQUILIBAR減壓調節器
EQUILIBAR電子壓力調節器
EQUILIBAR壓力調節器GP1BNISZP1000PSG1規格描述
Specification | |||
ELECTRICAL | MINIMUM | TYPICAL | MAXIMUM |
Supply Voltage | 15VDC | - | 24VDC |
Supply Current | 100mADC | - | 950mADC |
Command Signal | |||
Voltage | 0VDC | - | 10VDC |
Current | 4mADC | - | 20mADC |
Analog Monitor Output | |||
Voltage | 0VDC | - | 10VDC |
Current | 4mADC | - | 20mADC |
TTL | |||
Satisfied | - | 0VDC | - |
Not-Satisfied | - | 5VDC | - |
2nd Loop Input | OVDC | - | 10VDC |
PNEUMATIC | MINIMUM | TYPICAL | MAXIMUM |
Inlet Pressure 1 | Vacuum | 110% of full scale calibration | 1100 psig (75.8 bar(g))2 |
Pressure Range 1, 3 | Vacuum | - | 1000 psig (68.9 bar(g)) |
Flow Rate | 0 | - | 10 SCFM (17 m3/hr) |
Filtration Required | 40 micron | 20 micron (supplied with unit) | - |
Accuracy (Pressure) | ±0.1%F.S. | ±0.25%F.S. | ±0.5%F.S. |
Accuracy (Monitor) | - | ±0.3%F.S. | ±0.5%F.S. |
Hysteresis 4 | ±0.2%F.S. | ±0.02%F.S. | ±0.5%F.S. |
Port Size (all) | - | 1/8 inch NPT female (1/8 inch BSPP optional) | - |
Critical Volume 5 | - | 3 in3 | - |
PHYSICAL | MINIMUM | TYPICAL | MAXIMUM |
Operating Temperature | 32°F (0°C) | - | 158°F (70°C) |
Environment Protection 6 | - | - | NEMA 4 (IP65) |
Weight | - | Brass 3.75 LBS (1.75 KG) | - |
Electrical Connector | - | 6 pin molded 16 gauge wire | - |
EQUILIBAR壓力調節器GP1BNISZP1000PSG1產品介紹
Equilibar GP系列控制閥是一種電子壓力調節器，旨在在高達1000 psig（69 bar（g））的壓力范圍內精確控制與電子信號成比例的氣態介質壓力。
GP1由兩個常閉電磁閥，一個壓力傳感器和一個控制電路組成。一個閥被致動以允許供應介質進入系統。第二閥被致動以允許工作介質排放到大氣中。電子電路將內部壓力傳感器的反饋與用戶提供的電子指令信號進行比較，并致動適當?shù)拈y門，直到兩個信號匹配為止。
GP2與GP1相似，但使用雙回路控制方案。除了內部壓力傳感器之外，GP2還從外部傳感設備接收0-10Vdc反饋信號。外部信號用作主要反饋，并與命令信號進行比較。兩次比較之間的差異導致兩個電磁閥之一打開，從而允許流入或流出系統。
DS系列下游壓力傳感器將作為對GP2的第二個回路反饋。
GP系列可與多種一對一的高壓容積增壓器配合使用，以實現更大的流量。當使用音量增強器時，GP2可通過補償機械先導式調節器的滯后來提高精度。
GP系列產品帶有監視器輸出信號。該輸出是電信號，該電信號源自GP1閥控制電路中使用的內部傳感器。在GP2單元上，此信號來自外部傳感器。這樣就可以監視系統參數，并為數據采集需求提供信號。該信號的輸出可以配置為0-10Vdc或4-20mA。
The Equilibar GP series control valve is an electronic pressure regulator designed to precisely control the pressure of gaseous media proportional to an electronic signal in pressure ranges up to 1000 psig (69 bar(g)).
The GP1 consists of two normally closed solenoid valves, a pressure sensor, and a control circuit. One valve is actuated to allow supply media into the system. The second valve is actuated to allow working media to vent to atmosphere. An electronic circuit compares the internal pressure sensor feedback to the user supplied electronic command signal and actuates the appropriate valve until the two signals match.
The GP2 is similar to the GP1, but uses a double loop control scheme. In addition to the internal pressure transducer, the GP2 also receives a 0-10Vdc feedback signal from an external sensing device. The external signal functions as the primary feedback and is compared to the command signal. A difference between the two comparisons causes one of the two solenoid valves to open allowing flow in or out of the system.
A DS Series downstream pressure sensor will work as a second loop feedback to the GP2.
The GP series can be teamed with a variety of one-to-one ratio high pressure volume boosters for even greater flow. When using a volume booster, the GP2 can be used to achieve higher accuracy by compensating for the hysteresis of the mechanical pilot operated regulator.
GP series product comes with a monitor output signal. This output is an electrical signal originating from the internal sensor used in the control circuit of the GP1 valve. On GP2 units, this signal originates from the external transducer. This allows the system parameters to be monitored and provides a signal for data acquisition needs. The output of this signal can be configured to either 0-10Vdc or 4-20mA.
EQUILIBAR壓力調節器GP系列其他系列：
EQUILIBAR GP1
EQUILIBAR GP2
EQUILIBAR GP1BNISZP1000PSG1
EQUILIBAR GP1BNEEZP1000PSG1
EQUILIBAR Electropneumatic Regulators NEW + ORIGINAL+ ONE YEAR WARRANTY
愛澤工業成立于2010年，定位于向先進制造工業提供高端制造技術和設備。代理經營世界先進的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣，液壓以及氣動解決方案的合作伙伴，我們利用我們的全球協作團隊，為客戶提供先進解決方案，市場知識以及相關增值服務來幫助優化客戶的工作效率，提高可靠性和安全性，致力于成為工業產品和解決方案的優質渠道。
如果有任何關于EQUILIBAR壓力調節器GP1BNISZP1000PSG1的疑問，請隨時與我們溝通（021-31006702）。我們將盡全力解決您的問題。
If you have any question for EQUILIBAR products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website:jjxdch.cn.
EQUILIBAR壓力調節器GP1BNISZP1000PSG1產品參數
