OIL CONTROL成立于1974年諾南托拉(現被博士力士樂收購），在意大利工業領域運動控制閥移動機械市場占有很高的市場容量，且業績在汽車和工程機械行業迅速增長。從最初的 overcentre閥起重機和高空作業平臺開始，公司開始成功地處理與其他液壓機械的兼容應用中，主要應用于負載移動機械的控制，如遠程處理，挖土機，絞車等工程機械。今天的OIL CONTROL公司，已是移動設備與機械領域的閥門領導者，可以提供1600種不同類型的閥門生產與設計。
REXROTH OIL CONTROL的主要產品有：換向閥，止回閥，電磁閥，平衡閥，球閥，插裝閥，單向閥，溢流閥，行程閥，驅動閥，安全閥，閥組，閥塊，電磁閥線圈，流量計等等。
REXROTH OIL CONTROL閥08.45.19-X-Y-Z規格描述
Technical data | |
Max. operating pressure | 410 bar (5945 psi) |
Max. flow | 60 l/min. (16 gpm) |
Weight | see “Dimensions” |
Manifold material | Zinc plated steel |
Flange seal kit 1) | E00000000000056 (R930060579) |
Fluid | Mineral oil (HL, HLP) according DIN 51524 |
Fluid temperature range | -30 °C to 100 (-22 to 212 °F) |
Viscosity range | 5 to 800 mm2/s (cSt) |
Recommended degree of fluid contamination | Class 19/17/14 according to ISO 4406 |
MTTFd | 150 years see data sheet 18350-51 |
Other technical data | see data sheet 18350-50 |
Relief setting: at least 1.3 times the highest expected load. | |
1) Seals for 10 valves. | |
REXROTH OIL CONTROL閥08.45.19-X-Y-Z系列尺寸圖
REXROTH OIL CONTROL閥08.45.19-X-Y-Z選型及介紹
Description
When pressure at V2 rises above the spring bias pressure, the check seat is pushed away from the piston and flow is allowed from V2 to C2. When load pressure at C2 rises above the pressure setting, flow is relieved from C2 to V2. With pilot pressure at V1–C1, the pressure setting is reduced in proportion to the stated ratio of the valve, until opening and allowing flow from C2 to V2. The spring chamber is drained to V2. The valve applies a balanced piston and relief is operated at the valve setting independent of back-pressure at V2. However, the piloted opening of the valve remains subject to additive pressure at port V2. For safety and compactness, the C2 port is gasket mounted the actuator.
Note: port identified with M are not protected with calibrated orifice but in direct connection with pressure channels.
描述
當V2處的壓力上升到高于彈簧偏置壓力時，止回閥座被推離活塞，并允許從V2到C2的流量。 當C2處的負載壓力上升到壓力設定值以上時，流量從C2釋放到V2。 在先導壓力為V1-C1的情況下，壓力設定值按閥的規定比例成比例減小，直到打開并允許從C2到V2的流量為止。 彈簧腔排空至V2。 閥門使用平衡活塞，并且在閥門設定值下操作安全閥，而與V2的背壓無關。 但是，閥的先導打開仍會受到端口V2處附加壓力的影響。 為了安全和緊湊，C2端口通過墊圈安裝在執行機構上。
注意：標記為M的端口沒有經過校準的節流孔保護，而是與壓力通道直接連接。
REXROTH OIL CONTROL閥A-VBSO-SE-CC-30-PL-FC1系列其他常用型號：
REXROTH OIL CONTROL 08451903022000A R930050435
REXROTH OIL CONTROL 08451903023500B R930006213
REXROTH OIL CONTROL 08451903032000A R930007175
REXROTH OIL CONTROL 08451903033500B R930007174
REXROTH OIL CONTROL valve NEW + ORIGINAL+ ONE YEAR WARRANTY
愛澤工業成立于2010年，定位于向先進制造工業提供高端制造技術和設備。代理經營世界先進的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣，液壓以及氣動解決方案的合作伙伴，我們利用我們的全球協作團隊，為客戶提供先進解決方案，市場知識以及相關增值服務來幫助優化客戶的工作效率，提高可靠性和安全性，致力于成為工業產品和解決方案的優質渠道。
如果有任何關于REXROTH OIL CONTROL閥 08451903033500B R930007174的疑問，請隨時與我們溝通（021-31006702）。我們將盡全力解決您的問題。
If you have any question for REXROTH OIL CONTROL products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website: jjxdch.cn.
REXROTH OIL CONTROL閥 08451903033500B R930007174技術數據
