ETAS成立于1994 年，為Robert Bosch GmbH的子公司
Size and Weight | |
Dimensions (HxWxD) | 24 mm x 48 mm x 86.7 mm / 0.94 in x 1.89 in x 3.40 in (housing) |
Dimension with the Integrated Cable | 24 mm x 48 mm x 1586.7 mm / 0.94 in x 1.89 in x 624.68 in |
Weight | 0.15Kg / 0.33 lb (with cable) |
Environment | |
Temperature range | -40 °C to +70 °C / -40 °F to +158 °F (operation) |
-40 °C to +85 °C / -40 °F to +185 °F (transport and storage) | |
Relative humidity | 95% Max |
Ingress protection | IP52 |
Power supply | |
Current consumption | Power provided by USB port of the host PC or notebook |
Operating Voltage Range | 4.75 V – 5.25 V DC (Supply via USB port) |
Operating Current Range | 0.35 A (Max) at 5 V DC |
CAN FD / CAN interfaces | |
Number of channels | 2 |
CAN/CAN FD | CAN FD SIC : 5Mbit/ sec (higher number of nodes and sub-topology), 8Mbit/ sec (point to point connection), 64 Bytes (Payload) |
Protocols | CCP (not for CAN FD), XCP, KWP-on-CAN (ISO 14230/ISO 15765), UDS (ISO 14229/ISO 15765), CAN Monitoring, OBD-on-CAN (ISO 15765-4) |
CAN-Transceiver (Physical Layer) | TJA1044G |
Maximum baud rate for CAN | 1 Mbit/s |
Maximum baud rate for CANFD | 5 Mbit/s (Higher boud rates are possible at optimal environment and topology conditions) |
Electrical isolation | Interface is electrically isolated |
Acquisition of synchronous data | INCA synchronizes ECU data from the ES582 module with signals from measurement modules (e.g., from ES4xx or ES6xx modules) and ECUs with ETK or XETKs interface |
PC interface | |
USB | USB 2.0, High Speed |
Host system requirements | |
Operating system | Windows? 7, 8, 10, 11 |
Status display | |
LEDs | Operating state, interfaces |
Software support | |
Firmware Update | Support onwards HSP V14.1.0 |
INCA | Supported starts from INCA V7.2.3 for 5 MBaud and 7.5.0 for 8MBaud |
Delivery content | CAN Bus Interface USB Module, CAN-Y-cable, driver installation CD and user manual |
ETAS總線接口ES582.2系列介紹
ES582 – USB CAN FD 總線接口
ES582.2 模塊是一種雙通道、緊湊且經濟高效的 CAN FD 接口。該模塊是一種具有靈活數據速率支持的解決方案，用于將 PC 或筆記本電腦連接到車輛 CAN（控制器局域網絡）總線或車輛上各個電子控制單元 (ECU) 的 CAN 端口。
ES582 模塊通過 USB 連接到 PC 或筆記本電腦。該模塊由 PC 或筆記本電腦供電，無需外部電源。安裝和配置只需最少的努力。
測量數據由 ES582 模塊記錄。所有 ES582 測量數據都由 INCA 與來自其他 ECU 和測量模塊的信號精確同步。除了測量 ECU 信號外，INCA 還可以使用 ES582 模塊校準 ECU 參數、重新編程 ECU 的閃存或進行 ECU 診斷。
CAN FD SIC（信號改善能力）
CAN FD SIC（具有靈活數據速率和信號改善能力的收發器的 CAN）是博世開發的改進的向后兼容 CAN 協議。與 CAN 的主要區別在于，每條消息的有效載荷數據從 8 個字節增加到 64 個字節，傳輸速度高達 8 Mbit/s，校驗和更長，從而提高了傳輸可靠性。CAN FD SIC 滿足了汽車行業對更高網絡帶寬的需求。同時，CAN FD 節點可以輕松集成到現有的 CAN 基礎設施中。
優點
緊湊且經濟高效的雙通道 CAN FD SIC 總線接口，適用于 PC
支持符合 ISO 和不符合 ISO（CAN FD V1）版本的 CAN FD 協議
Y 型電纜用于連接交付中包含的接口模塊的兩個 CAN 通道
通過 USB 接口簡單直接地連接到主機 PC
針對測量數據記錄、ECU 校準、診斷和閃存編程任務進行了優化
與 INCA 完全集成
CAN 接口和主機 PC 的電氣隔離
ES582 支持 CAN FD，是傳統 CAN 和 CAN FD 領域廣泛應用的理想工具。例如，它可以通過診斷服務端口連接到車輛 CAN。ES582 支持所有 CAN 協議，例如 INCA 使用的 CCP、XCP、KWP-on-CAN 和 UDS。協議 CCP 和 KWP-on-CAN (ISO14230/ISO15765) 僅在 CAN 模式下受支持。
對于車輛驗證，用于 ECU 診斷的 INCA 附加組件 ODX-LINK 可以使用 ES582 訪問 OBD-on-CAN 功能以及讀取和清除診斷故障代碼 (DTC)，從而有效地消除了使用單獨診斷服務工具的需要。ES582 還提供 SAE J2534 直通接口，用于車輛診斷和使用第三方應用程序重新編程。
ES582 – USB CAN FD Bus Interface
The ES582.2 module is a dual-channel, compact and cost effective CAN FD interface. The module is a solution with flexible data rate support for connecting the PC or notebook to vehicle CAN (Controller Area Network) busses or the CAN port of individual electronic control units (ECU) on the vehicle.
The ES582 module connects with a PC or notebook over USB. The module gets power supply by the PC or notebook and no external power supply is needed. Installation and configuration require only minimum effort.
Measurement data are recorded by the ES582 module. All ES582 measurement data are accurately synchronized by INCA with signals from other ECUs and measurement modules. In addition to measuring ECU signals, INCA can use the ES582 module to calibrate ECU parameters, to reprogram an ECU’s flash memory, or for ECU diagnostics.
CAN FD SIC (Signal Improvement Capability)
CAN FD SIC (CAN with flexible data rate and signal improvement capable transceiver) is an improved, backward-compatible CAN protocol developed by Bosch. The principal differences to CAN consist in the increased payload data per message from 8 up to 64 bytes, the higher transmission speeds of up to 8 Mbit/s, and the longer checksums, which enhance transfer reliability. CAN FD SIC meets the automotive industry’s need for higher bandwidth for networks. At the same time, CAN FD nodes can be easily integrated into existing CAN infrastructure.
Benefits
Compact and cost-effective dual channel CAN FD SIC bus interface for PC
Supports both ISO-conform and non-ISO-conform (CAN FD V1) Version of the CAN FD protocol
Y-cable for connecting both CAN channels of the interface module included in the delivery
Simple and direct connection to the host PC via USB interface
Optimized for recording of measurement data, ECU calibration, diagnostics, and flash programming tasks
Fully integrated with INCA
Electrical isolation of CAN interface and host PC
The ES582 with its CAN FD support is an ideal tool for a wide range of applications for both in classical CAN and in CAN FD area. For example, it can be connected to a vehicle CAN via the diagnostics service port. The ES582 supports all CAN protocols, e.g CCP, XCP, KWP-on-CAN, and UDS used by INCA. The protocols CCP and KWP-on-CAN (ISO14230/ISO15765) are only supported in CAN mode.
For vehicle validation, ODX-LINK, the INCA add-on for ECU diagnostics, can use the ES582 to access OBD-on-CAN functionality as well as to read and clear Diagnostic Trouble Codes (DTCs), effectively eliminating the need for the use of a separate diagnostic service tool. ES582 also provides a SAE J2534 Pass Thru Interface for vehicle diagnostics and reprogramming with third party applications.
ETAS總線接口其他常用型號：
ETAS ES582.2
ETAS ES583
ETAS ES584
ETAS Brake disc NEW + ORIGINAL+ ONE YEAR WARRANTY
愛澤工業成立于2010年，定位于向先進制造工業提供高端制造技術和設備。代理經營世界先進的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣，液壓以及氣動解決方案的合作伙伴，我們利用我們的全球協作團隊，為客戶提供先進解決方案，市場知識以及相關增值服務來幫助優化客戶的工作效率，提高可靠性和安全性，致力于成為工業產品和解決方案的優質渠道。
如果有任何關于ETAS總線接口ES582.2的疑問，請隨時致電我們，愛澤工業（021-31006702）。我們將盡全力解決您的問題。
If you have any question for ETAS products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website: jjxdch.cn.
ETAS總線接口ES582.2參數介紹
